Hosokawa/Mikro Mikro-Atomizer Model 8MA spare parts. Includes swinging stirrup hammer rotor. Rotor is constructed of 304 stainless steel. This rotor was refurbished prior to being put into storage. The rotor comes with a 4 wheel especially design storage cart. There are 5 spare herring bone replacement strike plates. A 8MA requires 4 plates. They are constructed of carbon steel. There are also 2 carbon steel bearing housings. Also included are various retaining and spacing rings.
Marion 45 cu ft carbon steel paddle blender batch mixer. Series 4000, model 4020. Batch paddle mixer has a 45 cu ft working capacity and a 62 cu ft total volume. Mixer is driven by a 20 hp 1755 rpm motor through gear reducer down to 38 rpm. The mixer is an open top with a 36″ x 35.75″ opening and a 36″ x 14.25″ opening. The mixer bottom has an 8″ diameter flanged center discharge with butterfly valve 32″ from ground. The mixer has 36″ diameter paddles with a 2.75″ diameter shaft. Mixing chamber is 72″ long x 36″ wide x 45″ deep. Overall dimensions are 56″ wide x 114″ long x 85″ tall. Serial number 77091. Requires 230/ 460 vac 3 phase electrical supply.
140 gallon vertical stainless steel tank. This tank has an open top and a sloped bottom. The diameter is 37.5″, the overall height with agitator is 38″, and the straight side height is 30″. The side has a 1.5″ NPT discharge 4″ from the ground.
Thiele Engineering Co reciprocating placer model 208 RECIP PLACER. Reciprocating placer or tray denester has a dual arm pick mechanism, is on an adjustable stand, and can place up to an estimated 60 coupons per minute. Reciprocating placer has a product size range from 1″ long x 1″ wide to 16″ long x 20″ wide. Reciprocating placer’s approximate placing height ranges from 38″ – 48″ tall. Overall dimensions are 52″ long x 50″ wide x 86″ tall .115 vac 1 phase electric power and air required. Serial number 57431. Good condition.
Mueller 1,055 gallon vertical stainless steel tank. This tank has a closed top and an inverted dish bottom. The diameter is 77″, the overall height with agitator is 104″, and the straight side height is 58″. The top has a Lighnin ND-4B 3 hp 1755 rpm agitator, 13″ diameter inlet, and a 23.5″ x 23.5″ manway. The inside has 2.25″ od diameter coils that make 5 passes with the 1″ inlet and 1″ outlet out the top. The side has (1) 1.5″ NPT, (2) 2″ flanges, (3) 4″ flanges, and (1) 2″ NPT outlet 9″ from the ground. Requires 230/460 vac 3 phase electrical supply.
- Used Vertical Tank
MRM/Elgin Corp Titan 6 piston filler. Filler has stainless steel contact parts. The pistons are 6″ diameter x 14″ long. Valves have a 1″ diameter with 6″ centers and 1.25″ diameter change parts for wider mouth bottles. Filler has a 1-gallon max fill. It is equipped with a 40 gallon stainless steel hopper. Requires 230/460 vac 3 phase electrical supply.(Unit is missing components of control system)
MRM Elgin model E 16 station rotary tube filler and sealer for plastic tubes. Capable of filling tubes from 1.65 oz to 16 oz. Currently set for 5 oz on 4″ centers. Tube filler is equipped with tube counter and bottom fill; tubes are raised up to fill from bottom up. Tube passes through heating zone and then crimped shut with water cooled jaws. Tube filler also comes with a stainless steel hopper. Serial # 74045. Requires 220 vac 3 phase electrical supply and 100 psi air and cooling water supply. Tested in working condition. Manual and test video is available.
Hema Model MR50 rotary piston filler. 50 head filler. 304 stainless steel contact parts. Set for 307 x 111 cans at 1200 units per minute. Pistons are 1.968″ in diameter with a volume of 21.36 cu.in. Equipped with 290 gallon hopper. Filler has a no can/ no fill system. Driven by 12 hp drive motor. Requires 480 vac 3 ph electrical supply. Good Condition.
340 gallon Groen jacketed stainless steel flat bottom processing kettle. Model number AM 300. Jacket has a maximum working pressure of 30 psi. (No National Board stamp) Jacket has (2) 1.5” NPT fittings. Top of processor has an agitator bridge with 1 hp sweep agitator, 2.5” NPT fitting, 2.5” sanitary Tri-Clamp fitting, and a 2” sanitary Tri-Clamp fitting. Bottom has a 3” sanitary Tri-Clamp side discharge and 1.5” sanitary Tri-Clamp fitting. Measures 47” in diameter x 47” straight side and including (4) legs and agitator has an overall height of 74”. Processor has (2) 1/3 hinged lids with gating. Serial number 89539. Good Conditon.










